AIRTRONICS VG6000 MANUAL PDF

AIRTRONICS VG6000 MANUAL PDF

GHz FHSS-1 RX 6-Channel Full-Range Receiver Operating Instructions Use this receiver with your Airtronics RDS GHz transmitter or . We appreciate your purchase of this new AIRTRONICS. VG or VG Radio System. These instructions are intended to acquaint you with the many unique. Airtronics/Sanwa VG Modes? Radios. All; Planes; Sailplanes; Helis; FPV; Multirotors; Cars; Boats. About Sanwa VG Here you can.

Author: Nekazahn Vule
Country: Brazil
Language: English (Spanish)
Genre: History
Published (Last): 25 August 2010
Pages: 112
PDF File Size: 11.44 Mb
ePub File Size: 17.42 Mb
ISBN: 787-7-56708-795-9
Downloads: 96487
Price: Free* [*Free Regsitration Required]
Uploader: Vilkree

The VG is packed with all of the capabilities that the beginner as well as the more advanced modelers demand.

Airtronics VG6000 Transmitter dual charger battery pack manual remote control

Don’t show me this message again. On a fully charge battery, you may see airtroincs voltage as high as If there is a problem with servo movement, try moving to a different position while still maintaining the same distance from airtroncis model, then airtronic servo movement again. DO NOT operate your model again until you are certain the problem has been corrected. To the best of our knowledge, these tests were.

Doing so may cause loss of transmitter output, making it impossible to control your model. You will use two servos on two seprate channels to mix both ailerons and elevator together using only the left and right wing controls. Your model can cause serious damage or injury, so please use caution and courtesy at all times.

REV is available on all channels. This ensures that your radio control system does not get hit by interference.

You only need to read the introduction section and the one that applies to your type of model. To adjust stick length, hold Part B with your fingers and unscrew Maanual A counterclockwise to loosen the two pieces. Always before use, conduct a bench test to ensure that the servos operate properly. To the best of our knowledge, these tests were performed using measurement procedures consistent with industry or Commission standards and demonstrate that the equipment complies with the appropriate standards.

  AMBER DICELESS PDF

When the binding procedure is successful, the Bind Zirtronics on the receiver will stay solid blue when both the transmitter and receiver are turned ON.

Airtronics VG Manuals

Check to make sure that all receiver, vg600, switch, and onboard battery connections are correct and secure. By moving the Dual Rate Elevator switch you can see the 1 and 2 turn off and on in conjunction with the switch location 1 or 2. Page 20 Vb6000 settings are saved automatically on all models. We recommend that you bind the transmitter and receiver prior to mounting the receiver into your model. This will ensure that the transmitter and receiver are communicating properly prior to flight.

Alternatively, cut two short pieces of plastic tube and slide one antenna reception wire into each piece of tube, then tape or glue the tube to your model. Mwnual battery pack and antenna. What differential does is actually change the amount of aileron movement percentage between the aileron being in the up position compared to the down position.

Do not cut or extend the receiver antenna wires. If the throttle stick is not in the low position, when you turn it on, you will hear a continuous beeping sound and the display will read Aurtronics. For airrtonics information, see page 3. VG This equipment has been tested in accordance with the requirements contained in the appropriate Commission regulations.

Make sure that the receiver, servo sand switch harness connectors are securely fitted. If you have little to no experience operating models, we strongly recommend you seek the assistance of experienced modelers or your local hobby shop for guidance.

This will ensure that your model receives control signals no matter what its posture, attitude, or heading. Mankal ordinary crystal-based systems, your model can be used without frequency control.

  CONVERSOR DE RML PARA PDF

Airtronics VG transmitter – RC Groups

Check to ensure that the antenna wires are correctly mounted. Don’t have an account? Before use, double-check that the transmitter and receiver batteries are sufficiently charged. There is a danger of runaway operation if connectors shake loose during use. Programmable Fail Safe is available on channels 1 through 4 only.

Airtronics has invested a large amount of design effort to ensure that the powerful capabilities of the VG are as simple as possible to use.

If mounting the receiver surrounded by conductive materials for example, a carbon fiber fuselagemount the receiver so that the antenna reception wires can be extended outside of the model. The throttle cut feature will do just that. Also, wire mesh and similar barriers can adversely affect operation. When installing the receiver, the antenna reception wires the thin tip at the end of the coaxial cables should not come into contact with any carbon or metal components conductive components.

All your setting are saved in a eprom chip that does not need any type of battery to hold its memory. Add to my manuals Add. Once the binding process is complete, the setting is remembered even when the transmitter and receiver are turned Vg600, therefore, this procedure usually only needs to be done once for each separate receiver you’re using. Observe aortronics applicable laws and regulations in place at your flying site when using the 2.

Unlike frequency bands used with earlier radio control systems, reception with this 2. This equipment has been tested in accordance with the. Receiver Precautions l l l l l l l The receiver antenna wires consists of two coaxial cables and two reception wires the thin tip at the end of the coaxial cables.